The Experts below are selected from a list of 9 Experts worldwide ranked by ideXlab platform
Xiang Z. Kong - One of the best experts on this subject based on the ideXlab platform.
-
Influence of ingredients in water-based polyurethane-acrylic hybrid latexes on latex properties
Progress in Organic Coatings, 2008Co-Authors: Xiaoli Zhu, Xubao Jiang, Zhiguo Zhang, Xiang Z. KongAbstract:Abstract Polyurethane–acrylic (PU–AC) hybrid latexes were prepared. Main monomers for PU preparation were isophorone diisocyanate, DMPA (dimethylol propanic acid) and Polypropylene Oxides (PPO) of different molecular weights. Acrylic monomers included butyl acrylate, methyl methacrylate and a crosslinker, trihydroxymethyl propane triacrylates (TMPTA). Several important ingredients in PU–AC latex preparation, such as surfactants, initiator, DMPA and PU/AC ratio, etc., were varied, and their effects on latex properties studied. Compared with surfactant free latexes, a sharp increase in particle size was observed in latexes done with 0.1% of surfactant regardless of the nature of the surfactants used (anionic, nonionic and anionic with long chain of amphiphilic alkylphenyl polyethoxylate). Further increase in surfactant content, however, led to latexes with smaller particle size and narrower particle size distribution when compared between latexes prepared using a same surfactant. When amount of the oil soluble initiator, azobisisobutyronitrile, was increased, AC monomers conversion was increased. It is interesting to observe that PPO with long propylene Oxides brought about larger particle size combined with broader size distribution and less charge on particle surface; whereas lower DMPA levels led to latexes also of larger size combined with broader size distribution but more charges on particle surface. AC monomer crosslinker, TMPTA, contributed to reduce particle size, narrower size distribution and lower particle surface charges. By increasing AC amount in PU–AC latex, latex particle size significantly increased accompanied by a remarkable increase in particle surface charges. Mechanisms of particle formation and of DMPA stabilization were discussed in order to understand the experimental results.
Xiaoli Zhu - One of the best experts on this subject based on the ideXlab platform.
-
Influence of ingredients in water-based polyurethane-acrylic hybrid latexes on latex properties
Progress in Organic Coatings, 2008Co-Authors: Xiaoli Zhu, Xubao Jiang, Zhiguo Zhang, Xiang Z. KongAbstract:Abstract Polyurethane–acrylic (PU–AC) hybrid latexes were prepared. Main monomers for PU preparation were isophorone diisocyanate, DMPA (dimethylol propanic acid) and Polypropylene Oxides (PPO) of different molecular weights. Acrylic monomers included butyl acrylate, methyl methacrylate and a crosslinker, trihydroxymethyl propane triacrylates (TMPTA). Several important ingredients in PU–AC latex preparation, such as surfactants, initiator, DMPA and PU/AC ratio, etc., were varied, and their effects on latex properties studied. Compared with surfactant free latexes, a sharp increase in particle size was observed in latexes done with 0.1% of surfactant regardless of the nature of the surfactants used (anionic, nonionic and anionic with long chain of amphiphilic alkylphenyl polyethoxylate). Further increase in surfactant content, however, led to latexes with smaller particle size and narrower particle size distribution when compared between latexes prepared using a same surfactant. When amount of the oil soluble initiator, azobisisobutyronitrile, was increased, AC monomers conversion was increased. It is interesting to observe that PPO with long propylene Oxides brought about larger particle size combined with broader size distribution and less charge on particle surface; whereas lower DMPA levels led to latexes also of larger size combined with broader size distribution but more charges on particle surface. AC monomer crosslinker, TMPTA, contributed to reduce particle size, narrower size distribution and lower particle surface charges. By increasing AC amount in PU–AC latex, latex particle size significantly increased accompanied by a remarkable increase in particle surface charges. Mechanisms of particle formation and of DMPA stabilization were discussed in order to understand the experimental results.
Xubao Jiang - One of the best experts on this subject based on the ideXlab platform.
-
Influence of ingredients in water-based polyurethane-acrylic hybrid latexes on latex properties
Progress in Organic Coatings, 2008Co-Authors: Xiaoli Zhu, Xubao Jiang, Zhiguo Zhang, Xiang Z. KongAbstract:Abstract Polyurethane–acrylic (PU–AC) hybrid latexes were prepared. Main monomers for PU preparation were isophorone diisocyanate, DMPA (dimethylol propanic acid) and Polypropylene Oxides (PPO) of different molecular weights. Acrylic monomers included butyl acrylate, methyl methacrylate and a crosslinker, trihydroxymethyl propane triacrylates (TMPTA). Several important ingredients in PU–AC latex preparation, such as surfactants, initiator, DMPA and PU/AC ratio, etc., were varied, and their effects on latex properties studied. Compared with surfactant free latexes, a sharp increase in particle size was observed in latexes done with 0.1% of surfactant regardless of the nature of the surfactants used (anionic, nonionic and anionic with long chain of amphiphilic alkylphenyl polyethoxylate). Further increase in surfactant content, however, led to latexes with smaller particle size and narrower particle size distribution when compared between latexes prepared using a same surfactant. When amount of the oil soluble initiator, azobisisobutyronitrile, was increased, AC monomers conversion was increased. It is interesting to observe that PPO with long propylene Oxides brought about larger particle size combined with broader size distribution and less charge on particle surface; whereas lower DMPA levels led to latexes also of larger size combined with broader size distribution but more charges on particle surface. AC monomer crosslinker, TMPTA, contributed to reduce particle size, narrower size distribution and lower particle surface charges. By increasing AC amount in PU–AC latex, latex particle size significantly increased accompanied by a remarkable increase in particle surface charges. Mechanisms of particle formation and of DMPA stabilization were discussed in order to understand the experimental results.
Zhiguo Zhang - One of the best experts on this subject based on the ideXlab platform.
-
Influence of ingredients in water-based polyurethane-acrylic hybrid latexes on latex properties
Progress in Organic Coatings, 2008Co-Authors: Xiaoli Zhu, Xubao Jiang, Zhiguo Zhang, Xiang Z. KongAbstract:Abstract Polyurethane–acrylic (PU–AC) hybrid latexes were prepared. Main monomers for PU preparation were isophorone diisocyanate, DMPA (dimethylol propanic acid) and Polypropylene Oxides (PPO) of different molecular weights. Acrylic monomers included butyl acrylate, methyl methacrylate and a crosslinker, trihydroxymethyl propane triacrylates (TMPTA). Several important ingredients in PU–AC latex preparation, such as surfactants, initiator, DMPA and PU/AC ratio, etc., were varied, and their effects on latex properties studied. Compared with surfactant free latexes, a sharp increase in particle size was observed in latexes done with 0.1% of surfactant regardless of the nature of the surfactants used (anionic, nonionic and anionic with long chain of amphiphilic alkylphenyl polyethoxylate). Further increase in surfactant content, however, led to latexes with smaller particle size and narrower particle size distribution when compared between latexes prepared using a same surfactant. When amount of the oil soluble initiator, azobisisobutyronitrile, was increased, AC monomers conversion was increased. It is interesting to observe that PPO with long propylene Oxides brought about larger particle size combined with broader size distribution and less charge on particle surface; whereas lower DMPA levels led to latexes also of larger size combined with broader size distribution but more charges on particle surface. AC monomer crosslinker, TMPTA, contributed to reduce particle size, narrower size distribution and lower particle surface charges. By increasing AC amount in PU–AC latex, latex particle size significantly increased accompanied by a remarkable increase in particle surface charges. Mechanisms of particle formation and of DMPA stabilization were discussed in order to understand the experimental results.
M M Abdelhamid - One of the best experts on this subject based on the ideXlab platform.
-
preparation of some thermal stable polymers based on diesters of polyethylene and Polypropylene Oxides macro monomers to use as surfactants at high temperature and pressure
Egyptian Journal of Petroleum, 2016Co-Authors: A M Alsabagh, M E Hassan, S D M Dosouky, N M Nasser, E A Elsharaky, M M AbdelhamidAbstract:Abstract Based on polyethylene (PE) and Polypropylene (PP) Oxides, six macromonomers were prepared through two steps. The first step was esterification of the PE and PP Oxides, with oleic acid to give the corresponding monoesters. The second was the diesterfication of the prepared monoesters with methacrylic acid to give the corresponding diesters. The prepared macromonomers (diesters) were polymerized to obtain six polymers. The chemical structure of the prepared mono- and diesters and polymers was justified by IR, NMR, GPC and TGA. The obtained results confirmed that the prepared polymers have a high thermal stability and can be used in high pressure and temperature during the drainage of the water from water-in-oil emulsions. The surface active and thermodynamics parameters of these polymers in non-aqueous solution were also investigated and it was found that, these materials have high thermal stability which leads to the possibility to be used under severe reservoir conditions as surfactants.