The Experts below are selected from a list of 165 Experts worldwide ranked by ideXlab platform

Ezio Spessa - One of the best experts on this subject based on the ideXlab platform.

  • Numerical-Experimental Study and Solutions to Reduce the Dwell-Time Threshold for Fusion-Free Consecutive Injections in a Multijet Solenoid-Type CR System
    Journal of Engineering for Gas Turbines and Power, 2008
    Co-Authors: Andrea Catania, Alessandro Ferrari, Ezio Spessa
    Abstract:

    In ‘Multijet’ Common Rail (C.R.) diesel injection systems, when two consecutive injection current-pulses are approached to each other, the fusion of the two injections can occur. This causes undesired excessive amount of injected fuel, which leads to worsening of particulate emissions and fuel consumption. In order to avoid such a phenomenon, lower limits to the values of dwell time are introduced in the control unit maps, by means of a conservatively overestimated threshold, limiting the flexible management of multiple injections and C.R. system capability to perform a larger number of injection shots. The reason of the injection fusion is mainly due to the time delay between the electrical signal to the solenoid and the needle lift at both valve opening and closure. In particular, the dwell-time range inside of which injection fusion occurs was shown to decrease by reducing the nozzle closure delay. Experimental tests were carried out on a high-performance Moehwald-Bosch MEP2000/CA4000 test bench for determining the functional dependence of nozzle closure and opening delays on solenoid energizing time and nominal rail pressure. Besides, a mathematical relation between the solenoid energizing time and the injection time interval was determined. A Multijet C.R. injection system mathematical model, that was previously developed, including thermodynamics of liquids, fluid dynamics, subsystem mechanics, and electromagnetism equations, was applied to better understand the cause and effect relationships for nozzle opening and closure delays. In particular, numerical results on the time histories of delivery- and control-chamber pressures, pilot- and needle-valve lifts, mass flow rates through Z and A holes, were obtained and analyzed in order to highlight the dependence of nozzle opening and closure delays on electro-injector internal geometric features and on the needle dynamics. For all the considered operating conditions, the model predictions were compared to the experimental injection flow-rate patterns and to the pressure data taken at the injector inlet, for assessment. The nozzle closure delay was shown to strongly depend on the needle dynamics. Parametric tests were carried out with the numerical code by changing needle and control plunger mass, needle Spring Preload and stiffness, maximum needle stroke, in order to identify configurations useful for minimizing the nozzle closure delay. On the basis of the indications derived from these numerical tests, a modified version of the commercial electro-injector was realized so as to achieve effectively reduced nozzle closure delays and very close sequential injections without any fusion between them.Copyright © 2006 by ASME

  • Numerical-Experimental Study and Solutions to Reduce the Dwell Time Threshold for Fusion-Free Consecutive Injections in a Multijet Solenoid-Type C.R. System
    ASME 2006 Internal Combustion Engine Division Spring Technical Conference (ICES2006), 2006
    Co-Authors: Andrea Emilio Catania, Alessandro Ferrari, Ezio Spessa
    Abstract:

    In ‘Multijet’ Common Rail (C.R.) diesel injection systems, when two consecutive injection current-pulses are approached to each other, the fusion of the two injections can occur. This causes undesired excessive amount of injected fuel, which leads to worsening of particulate emissions and fuel consumption. In order to avoid such a phenomenon, lower limits to the values of dwell time are introduced in the control unit maps, by means of a conservatively overestimated threshold, limiting the flexible management of multiple injections and C.R. system capability to perform a larger number of injection shots. The reason of the injection fusion is mainly due to the time delay between the electrical signal to the solenoid and the needle lift at both valve opening and closure. In particular, the dwell-time range inside of which injection fusion occurs was shown to decrease by reducing the nozzle closure delay. Experimental tests were carried out on a high-performance Moehwald-Bosch MEP2000/CA4000 test bench for determining the functional dependence of nozzle closure and opening delays on solenoid energizing time and nominal rail pressure. Besides, a mathematical relation between the solenoid energizing time and the injection time interval was determined. A Multijet C.R. injection system mathematical model, that was previously developed, including thermodynamics of liquids, fluid dynamics, subsystem mechanics, and electromagnetism equations, was applied to better understand the cause and effect relationships for nozzle opening and closure delays. In particular, numerical results on the time histories of delivery- and control-chamber pressures, pilot- and needle-valve lifts, mass flow rates through Z and A holes, were obtained and analyzed in order to highlight the dependence of nozzle opening and closure delays on electro-injector internal geometric features and on the needle dynamics. For all the considered operating conditions, the model predictions were compared to the experimental injection flow-rate patterns and to the pressure data taken at the injector inlet, for assessment. The nozzle closure delay was shown to strongly depend on the needle dynamics. Parametric tests were carried out with the numerical code by changing needle and control plunger mass, needle Spring Preload and stiffness, maximum needle stroke, in order to identify configurations useful for minimizing the nozzle closure delay. On the basis of the indications derived from these numerical tests, a modified version of the commercial electro-injector was realized so as to achieve effectively reduced nozzle closure delays and very close sequential injections without any fusion between them.

Andrea Catania - One of the best experts on this subject based on the ideXlab platform.

  • Numerical-Experimental Study and Solutions to Reduce the Dwell-Time Threshold for Fusion-Free Consecutive Injections in a Multijet Solenoid-Type CR System
    Journal of Engineering for Gas Turbines and Power, 2008
    Co-Authors: Andrea Catania, Alessandro Ferrari, Ezio Spessa
    Abstract:

    In ‘Multijet’ Common Rail (C.R.) diesel injection systems, when two consecutive injection current-pulses are approached to each other, the fusion of the two injections can occur. This causes undesired excessive amount of injected fuel, which leads to worsening of particulate emissions and fuel consumption. In order to avoid such a phenomenon, lower limits to the values of dwell time are introduced in the control unit maps, by means of a conservatively overestimated threshold, limiting the flexible management of multiple injections and C.R. system capability to perform a larger number of injection shots. The reason of the injection fusion is mainly due to the time delay between the electrical signal to the solenoid and the needle lift at both valve opening and closure. In particular, the dwell-time range inside of which injection fusion occurs was shown to decrease by reducing the nozzle closure delay. Experimental tests were carried out on a high-performance Moehwald-Bosch MEP2000/CA4000 test bench for determining the functional dependence of nozzle closure and opening delays on solenoid energizing time and nominal rail pressure. Besides, a mathematical relation between the solenoid energizing time and the injection time interval was determined. A Multijet C.R. injection system mathematical model, that was previously developed, including thermodynamics of liquids, fluid dynamics, subsystem mechanics, and electromagnetism equations, was applied to better understand the cause and effect relationships for nozzle opening and closure delays. In particular, numerical results on the time histories of delivery- and control-chamber pressures, pilot- and needle-valve lifts, mass flow rates through Z and A holes, were obtained and analyzed in order to highlight the dependence of nozzle opening and closure delays on electro-injector internal geometric features and on the needle dynamics. For all the considered operating conditions, the model predictions were compared to the experimental injection flow-rate patterns and to the pressure data taken at the injector inlet, for assessment. The nozzle closure delay was shown to strongly depend on the needle dynamics. Parametric tests were carried out with the numerical code by changing needle and control plunger mass, needle Spring Preload and stiffness, maximum needle stroke, in order to identify configurations useful for minimizing the nozzle closure delay. On the basis of the indications derived from these numerical tests, a modified version of the commercial electro-injector was realized so as to achieve effectively reduced nozzle closure delays and very close sequential injections without any fusion between them.Copyright © 2006 by ASME

Fangxi Xie - One of the best experts on this subject based on the ideXlab platform.

  • Effect of Multi-Factor Coupling on the Movement Characteristics of the Hydraulic Variable Valve Actuation
    Energies, 2020
    Co-Authors: Jin Zhaohui, Wei Hong, Tian You, Fangxi Xie
    Abstract:

    Studies show that the valve lift (VL) of the cam-driven hydraulic variable valve actuation (VVA) can be continuously adjusted in the range of 0–8.2 mm by controlling the opening of the throttling valve. In the present study, an orthogonal experiment with interaction was designed to analyze the effect of multi-factor coupling on the VL, valve-seating velocity (VSV), and pressure fluctuation in the valve piston cavity. In order to reduce the pressure fluctuation, the Taguchi method was applied to find the optimal combination of the key parameters including the diameter of the piston, the Spring Preload of the valve-seating buffer mechanism (VSBM), the Spring Preload of the valve, and the valve piston mass. The correctness of the VVA simulation model is verified through experiments. Moreover, the pressure fluctuation is analyzed through a numerical simulation. The obtained results showed that as long as the VSV is less than 0.5 m·s−1, the pressure fluctuations in hydraulic VVA can be reduced by several means, such as increasing the Spring stiffness of the VSBM and valve, increasing the valve piston area and diameter size of the thin-walled hole, and reducing the valve piston mass and total hydraulic oil volume.

Alessandro Ferrari - One of the best experts on this subject based on the ideXlab platform.

  • Numerical-Experimental Study and Solutions to Reduce the Dwell-Time Threshold for Fusion-Free Consecutive Injections in a Multijet Solenoid-Type CR System
    Journal of Engineering for Gas Turbines and Power, 2008
    Co-Authors: Andrea Catania, Alessandro Ferrari, Ezio Spessa
    Abstract:

    In ‘Multijet’ Common Rail (C.R.) diesel injection systems, when two consecutive injection current-pulses are approached to each other, the fusion of the two injections can occur. This causes undesired excessive amount of injected fuel, which leads to worsening of particulate emissions and fuel consumption. In order to avoid such a phenomenon, lower limits to the values of dwell time are introduced in the control unit maps, by means of a conservatively overestimated threshold, limiting the flexible management of multiple injections and C.R. system capability to perform a larger number of injection shots. The reason of the injection fusion is mainly due to the time delay between the electrical signal to the solenoid and the needle lift at both valve opening and closure. In particular, the dwell-time range inside of which injection fusion occurs was shown to decrease by reducing the nozzle closure delay. Experimental tests were carried out on a high-performance Moehwald-Bosch MEP2000/CA4000 test bench for determining the functional dependence of nozzle closure and opening delays on solenoid energizing time and nominal rail pressure. Besides, a mathematical relation between the solenoid energizing time and the injection time interval was determined. A Multijet C.R. injection system mathematical model, that was previously developed, including thermodynamics of liquids, fluid dynamics, subsystem mechanics, and electromagnetism equations, was applied to better understand the cause and effect relationships for nozzle opening and closure delays. In particular, numerical results on the time histories of delivery- and control-chamber pressures, pilot- and needle-valve lifts, mass flow rates through Z and A holes, were obtained and analyzed in order to highlight the dependence of nozzle opening and closure delays on electro-injector internal geometric features and on the needle dynamics. For all the considered operating conditions, the model predictions were compared to the experimental injection flow-rate patterns and to the pressure data taken at the injector inlet, for assessment. The nozzle closure delay was shown to strongly depend on the needle dynamics. Parametric tests were carried out with the numerical code by changing needle and control plunger mass, needle Spring Preload and stiffness, maximum needle stroke, in order to identify configurations useful for minimizing the nozzle closure delay. On the basis of the indications derived from these numerical tests, a modified version of the commercial electro-injector was realized so as to achieve effectively reduced nozzle closure delays and very close sequential injections without any fusion between them.Copyright © 2006 by ASME

  • Numerical-Experimental Study and Solutions to Reduce the Dwell Time Threshold for Fusion-Free Consecutive Injections in a Multijet Solenoid-Type C.R. System
    ASME 2006 Internal Combustion Engine Division Spring Technical Conference (ICES2006), 2006
    Co-Authors: Andrea Emilio Catania, Alessandro Ferrari, Ezio Spessa
    Abstract:

    In ‘Multijet’ Common Rail (C.R.) diesel injection systems, when two consecutive injection current-pulses are approached to each other, the fusion of the two injections can occur. This causes undesired excessive amount of injected fuel, which leads to worsening of particulate emissions and fuel consumption. In order to avoid such a phenomenon, lower limits to the values of dwell time are introduced in the control unit maps, by means of a conservatively overestimated threshold, limiting the flexible management of multiple injections and C.R. system capability to perform a larger number of injection shots. The reason of the injection fusion is mainly due to the time delay between the electrical signal to the solenoid and the needle lift at both valve opening and closure. In particular, the dwell-time range inside of which injection fusion occurs was shown to decrease by reducing the nozzle closure delay. Experimental tests were carried out on a high-performance Moehwald-Bosch MEP2000/CA4000 test bench for determining the functional dependence of nozzle closure and opening delays on solenoid energizing time and nominal rail pressure. Besides, a mathematical relation between the solenoid energizing time and the injection time interval was determined. A Multijet C.R. injection system mathematical model, that was previously developed, including thermodynamics of liquids, fluid dynamics, subsystem mechanics, and electromagnetism equations, was applied to better understand the cause and effect relationships for nozzle opening and closure delays. In particular, numerical results on the time histories of delivery- and control-chamber pressures, pilot- and needle-valve lifts, mass flow rates through Z and A holes, were obtained and analyzed in order to highlight the dependence of nozzle opening and closure delays on electro-injector internal geometric features and on the needle dynamics. For all the considered operating conditions, the model predictions were compared to the experimental injection flow-rate patterns and to the pressure data taken at the injector inlet, for assessment. The nozzle closure delay was shown to strongly depend on the needle dynamics. Parametric tests were carried out with the numerical code by changing needle and control plunger mass, needle Spring Preload and stiffness, maximum needle stroke, in order to identify configurations useful for minimizing the nozzle closure delay. On the basis of the indications derived from these numerical tests, a modified version of the commercial electro-injector was realized so as to achieve effectively reduced nozzle closure delays and very close sequential injections without any fusion between them.

Jin Zhaohui - One of the best experts on this subject based on the ideXlab platform.

  • Effect of Multi-Factor Coupling on the Movement Characteristics of the Hydraulic Variable Valve Actuation
    Energies, 2020
    Co-Authors: Jin Zhaohui, Wei Hong, Tian You, Fangxi Xie
    Abstract:

    Studies show that the valve lift (VL) of the cam-driven hydraulic variable valve actuation (VVA) can be continuously adjusted in the range of 0–8.2 mm by controlling the opening of the throttling valve. In the present study, an orthogonal experiment with interaction was designed to analyze the effect of multi-factor coupling on the VL, valve-seating velocity (VSV), and pressure fluctuation in the valve piston cavity. In order to reduce the pressure fluctuation, the Taguchi method was applied to find the optimal combination of the key parameters including the diameter of the piston, the Spring Preload of the valve-seating buffer mechanism (VSBM), the Spring Preload of the valve, and the valve piston mass. The correctness of the VVA simulation model is verified through experiments. Moreover, the pressure fluctuation is analyzed through a numerical simulation. The obtained results showed that as long as the VSV is less than 0.5 m·s−1, the pressure fluctuations in hydraulic VVA can be reduced by several means, such as increasing the Spring stiffness of the VSBM and valve, increasing the valve piston area and diameter size of the thin-walled hole, and reducing the valve piston mass and total hydraulic oil volume.