The Experts below are selected from a list of 17781 Experts worldwide ranked by ideXlab platform
Wu Jian - One of the best experts on this subject based on the ideXlab platform.
-
Design of Distributed Real-time System for Power Monitor
Computer Engineering, 2003Co-Authors: Wu JianAbstract:This article brings forward the ideas of using distributed system for real-time power monitor, gives designs for the system, analyzes the Main Technique fitting for it.
Zhou Zhi-min - One of the best experts on this subject based on the ideXlab platform.
-
Developing Dynamic of the Main Technique of Frequency Converters for Medium Voltage
Energy technology, 2002Co-Authors: Zhou Zhi-minAbstract:Developing dynamic of direct medium voltage converter Technique and indirect medium voltage converter is presented. The characteristics are described according to different control modes and different electronic elements of electric power in the Main circuit of indirect medium voltage converter Technique. The developing dynamic of the Main Technique of frequency converters for medium voltage is discussed.
Thierry Baudin - One of the best experts on this subject based on the ideXlab platform.
-
Texture of Rotary-Friction-Welded from Dissimilar Medium Carbon Steels
World Journal of Condensed Matter Physics, 2020Co-Authors: Zakaria Boumerzoug, Anne-laure Helbert, Francois Brisset, Elena Priymak, Anna Stepanchukova, Thierry BaudinAbstract:The purpose of the present study was to investigate the texture in dissimilar medium carbon steels welded by rotary friction Technique. The Electron Backscatter Diffraction (EBSD) Technique was the Main Technique used to investigate the effect of welding on grain size and grain crystallographic orientation in the welded joint. Moreover, the effect of isothermal heat treatment at 600˚C on welded joint has been studied knowing that this annealing allows to decrease the residual stresses. EBSD results revealed different subzones in welded joint. The texture in the weld is essentially composed of three components: Goss {110} , Rotated Cube {100} , and Rotated Goss {110} orientation. The heat treatments applied on welded material had a slight effect on texture and grain size.
-
Texture analysis of welded 304L pipeline steel
Journal of Metals Materials and Minerals, 2019Co-Authors: Soumia Hamza, Zakaria Boumerzoug, Anne-laure Helbert, Francois Brisset, Thierry BaudinAbstract:This present paper studied the effect of arc welding process on the crystallographic texture of pipeline 304L steel. The Electron Backscatter Diffraction (EBSD) Technique was the Main Technique used to illustrate the effect of welding on grain orientation in the fusion zone, in the heat affected zone, and in the base metal. Moreover, the effect of isothermal heat treatment at 400 °C on welded joint has been studied. It was found the same orientation in the base metal and the heat affected zone, however different and heterogeneous structures were observed in fusion zone. The applied heat treatments at 400°C on welded material had a slight effect on crystallographic texture, but it had an effect on grain size in fusion zone. .
Ju Hai - One of the best experts on this subject based on the ideXlab platform.
-
The characteristics and management system's development and research of the pollutant source's monitoring data
Environmental Monitoring in China, 2002Co-Authors: Ju HaiAbstract:The pollutant source's monitoring data resources are analysed detailedly on the angle of application software's exploitation On this base, the design thought, logic construction, module composition etc, the Main Technique problems in the course of developing pollutant source's monitoring data management system are then discussed and introduced
Dick Alstein - One of the best experts on this subject based on the ideXlab platform.
-
Dynamic reconfiguration in distributed hard real-time systems
1991Co-Authors: Dick AlsteinAbstract:The paper focuses on the problem of dynamic workload reconfiguration in distributed systems_ After the failure of a node, the processes that were allocated to that node must be redistributed among the reMaining nodes. The Main Technique considered is process redundancy. After an overview of design issues and solving Techniques, the relevant literature is discussed. Proposals are given for the methods to be used in the DEDOS project, with directions for further research.
