The Experts below are selected from a list of 483 Experts worldwide ranked by ideXlab platform
Assmussen Dennis - One of the best experts on this subject based on the ideXlab platform.
-
Kvalitetsförbättringar och Emballageinstruktioner
Mälardalens högskola Akademin för innovation design och teknik, 2014Co-Authors: Sadi Sarkat, Assmussen DennisAbstract:This report is the result of a thesis carried out at the Department of Innovation, Design and Technology (IDT), at Mälardalen University on behalf of ABB AB Machines.The year was 1988 when ASEA and Brown Boveri formed a joint venture under the name ABB (Asea Brown Boveri).We perform our thesis at the division Discrete Automation and Motion where they primarily develops, manufactures and sells synchronous and asynchronous AC motors and generators.The main purpose of this thesis was initially to write a general packaging Instruction, but the priority changed to develop more specific packaging Instructions for Rotors, Stator gables, Bearing support and Outer Cover (plates) instead.The work started off to deal with a problem about that the staff had to start its work to grind away rust on the stator gables due to those stored outdoors. The result was mainly an investment in a new gable rack so that the material can be stored inside, as well as a Packing Instruction as it was originally intended.The problem on the bearing supports were that the staff thought it was demanding and difficult to clean them from the rustproofing they were greased in. If it is not possible to remove all rust protection it can cause the paint to not attach properly. After having compared with similar articles a test were done to order a pair of bearing supports without corrosion inhibitor, which gave good results. This initiative also set in motion a process to do the same for more different items.For special pallet, a survey were made of the process with two different VSM and a calculation of how much ABB would earn at ordering more special pallets than getting the material delivered on the A-pallets. As a result, the recommendations to ABB where to purchase five special pallets to have a good moving flow.In the current situation rotors are delivered to ABB in three different ways, by three different suppliers. The current status were reviewed of those three suppliers and talking to the staff to choose which way that was best and then write a Packing Instruction accordingly to that.Denna rapport är resultatet av ett examensarbete utfört vid Institutionen för Innovation, Design och Teknik, (IDT), vid Mälardalens högskola på uppdrag av ABB AB Machines.Året var 1988 då ASEA och Brown Boveri bildade ett gemensamt företag under namnet ABB (Asea Brown Boveri).Examensarbetet utfördes på divisionen Disctrete Automation and Motion där de främst utvecklar, tillverkar och säljer synkrona och asynkrona växelströms- motorer och generatorer.Huvudsyftet med detta examensarbete var från början att skriva en generell emballageinstruktion, men prioriteringen ändrades till att ta fram mer specifika emballage instruktioner för Rotorer, Statorgavlar, Lagerstöd och Yttre kåpa (plåtar) istället.Arbetet började med att ta itu med ett problem om att personalen fick börja sitt arbete med att slipa bort rost på statorgavlarna pga. att dem förvaras utomhus. Resultatet blev främst en investering i ett nytt gavelställ så att materialet kan förvaras inomhus samt en emballageinstruktion som det var tänkt från början.Problemet angående lagerstöden var att personalen tyckte att det var krävande och svårt med rengöringen från rostskyddet lagerstöden var insmorda i. Om allt rostskydd inte går att få bort kan det leda till att målarfärgen inte fäster ordentligt. Efter att ha jämfört med liknande artiklar gjordes ett test att beställa ett lagerstöds par utan rostskyddsmedel, vilket gav ett bra resultat. Detta initiativ satte även igång en process för inköparna att göra samma sak för fler olika artiklar.För specialpallen gjordes en kartläggning av processen med två olika VSM samt att en beräkning gjordes på hur mycket ABB skulle tjäna på att beställa fler specialpallar än att få plåtdetaljerna levererade på A-pallar. Resultatet blev att vi rekommenderar ABB att köpa in 5 specialpallar till för att ha ett bra rullande flöde.I dagsläget levereras rotorer till ABB på tre olika sätt från tre olika leverantörer. Nuläget analyserades för dem tre leverantörerna för att sedan i samspråk med personalen välja vilket sätt som var bäst och skriva en emballageinstruktion utifrån det
Greg James - One of the best experts on this subject based on the ideXlab platform.
-
Preparing for Ebolavirus disease: specimen collection, packaging and transport.
Pathology, 2015Co-Authors: Sheena Adamson, Roger Wilson, Greg JamesAbstract:Summary Ebolavirus is classified by Standards Australia as a Risk Group 4 pathogen for handling in laboratories. Specimens known or reasonably expected to contain Ebolavirus are classified by the United Nations as Dangerous Goods Infectious Substances Category A, UN 2814, which if transported by air must comply with International Air Transport Association (IATA) Hazard Class 6.2 and Packing Instruction 620 and Civil Aviation Safety Authority (CASA) Regulations. As such high risk pathogens are rarely encountered in pathology laboratories in Australia, the possibility of an imported case of Ebolavirus disease occurring in NSW during the current ongoing outbreak which began in West Africa in 2014 prompted a review and rapid implementation of specific risk management protocols for Ebolavirus testing. Here we describe and report on the management of specimen collection, packaging and transport by public and private pathology laboratories agreed by a task force led by NSW Health Pathology and Health Protection NSW.
Dennis Assmussen - One of the best experts on this subject based on the ideXlab platform.
-
Kvalitetsförbättringar och Emballageinstruktioner
2014Co-Authors: Sarkat Sadi, Dennis AssmussenAbstract:This report is the result of a thesis carried out at the Department of Innovation, Design and Technology (IDT), at Malardalen University on behalf of ABB AB Machines.The year was 1988 when ASEA and Brown Boveri formed a joint venture under the name ABB (Asea Brown Boveri).We perform our thesis at the division Discrete Automation and Motion where they primarily develops, manufactures and sells synchronous and asynchronous AC motors and generators.The main purpose of this thesis was initially to write a general packaging Instruction, but the priority changed to develop more specific packaging Instructions for Rotors, Stator gables, Bearing support and Outer Cover (plates) instead.The work started off to deal with a problem about that the staff had to start its work to grind away rust on the stator gables due to those stored outdoors. The result was mainly an investment in a new gable rack so that the material can be stored inside, as well as a Packing Instruction as it was originally intended.The problem on the bearing supports were that the staff thought it was demanding and difficult to clean them from the rustproofing they were greased in. If it is not possible to remove all rust protection it can cause the paint to not attach properly. After having compared with similar articles a test were done to order a pair of bearing supports without corrosion inhibitor, which gave good results. This initiative also set in motion a process to do the same for more different items.For special pallet, a survey were made of the process with two different VSM and a calculation of how much ABB would earn at ordering more special pallets than getting the material delivered on the A-pallets. As a result, the recommendations to ABB where to purchase five special pallets to have a good moving flow.In the current situation rotors are delivered to ABB in three different ways, by three different suppliers. The current status were reviewed of those three suppliers and talking to the staff to choose which way that was best and then write a Packing Instruction accordingly to that.
Sadi Sarkat - One of the best experts on this subject based on the ideXlab platform.
-
Kvalitetsförbättringar och Emballageinstruktioner
Mälardalens högskola Akademin för innovation design och teknik, 2014Co-Authors: Sadi Sarkat, Assmussen DennisAbstract:This report is the result of a thesis carried out at the Department of Innovation, Design and Technology (IDT), at Mälardalen University on behalf of ABB AB Machines.The year was 1988 when ASEA and Brown Boveri formed a joint venture under the name ABB (Asea Brown Boveri).We perform our thesis at the division Discrete Automation and Motion where they primarily develops, manufactures and sells synchronous and asynchronous AC motors and generators.The main purpose of this thesis was initially to write a general packaging Instruction, but the priority changed to develop more specific packaging Instructions for Rotors, Stator gables, Bearing support and Outer Cover (plates) instead.The work started off to deal with a problem about that the staff had to start its work to grind away rust on the stator gables due to those stored outdoors. The result was mainly an investment in a new gable rack so that the material can be stored inside, as well as a Packing Instruction as it was originally intended.The problem on the bearing supports were that the staff thought it was demanding and difficult to clean them from the rustproofing they were greased in. If it is not possible to remove all rust protection it can cause the paint to not attach properly. After having compared with similar articles a test were done to order a pair of bearing supports without corrosion inhibitor, which gave good results. This initiative also set in motion a process to do the same for more different items.For special pallet, a survey were made of the process with two different VSM and a calculation of how much ABB would earn at ordering more special pallets than getting the material delivered on the A-pallets. As a result, the recommendations to ABB where to purchase five special pallets to have a good moving flow.In the current situation rotors are delivered to ABB in three different ways, by three different suppliers. The current status were reviewed of those three suppliers and talking to the staff to choose which way that was best and then write a Packing Instruction accordingly to that.Denna rapport är resultatet av ett examensarbete utfört vid Institutionen för Innovation, Design och Teknik, (IDT), vid Mälardalens högskola på uppdrag av ABB AB Machines.Året var 1988 då ASEA och Brown Boveri bildade ett gemensamt företag under namnet ABB (Asea Brown Boveri).Examensarbetet utfördes på divisionen Disctrete Automation and Motion där de främst utvecklar, tillverkar och säljer synkrona och asynkrona växelströms- motorer och generatorer.Huvudsyftet med detta examensarbete var från början att skriva en generell emballageinstruktion, men prioriteringen ändrades till att ta fram mer specifika emballage instruktioner för Rotorer, Statorgavlar, Lagerstöd och Yttre kåpa (plåtar) istället.Arbetet började med att ta itu med ett problem om att personalen fick börja sitt arbete med att slipa bort rost på statorgavlarna pga. att dem förvaras utomhus. Resultatet blev främst en investering i ett nytt gavelställ så att materialet kan förvaras inomhus samt en emballageinstruktion som det var tänkt från början.Problemet angående lagerstöden var att personalen tyckte att det var krävande och svårt med rengöringen från rostskyddet lagerstöden var insmorda i. Om allt rostskydd inte går att få bort kan det leda till att målarfärgen inte fäster ordentligt. Efter att ha jämfört med liknande artiklar gjordes ett test att beställa ett lagerstöds par utan rostskyddsmedel, vilket gav ett bra resultat. Detta initiativ satte även igång en process för inköparna att göra samma sak för fler olika artiklar.För specialpallen gjordes en kartläggning av processen med två olika VSM samt att en beräkning gjordes på hur mycket ABB skulle tjäna på att beställa fler specialpallar än att få plåtdetaljerna levererade på A-pallar. Resultatet blev att vi rekommenderar ABB att köpa in 5 specialpallar till för att ha ett bra rullande flöde.I dagsläget levereras rotorer till ABB på tre olika sätt från tre olika leverantörer. Nuläget analyserades för dem tre leverantörerna för att sedan i samspråk med personalen välja vilket sätt som var bäst och skriva en emballageinstruktion utifrån det
Sheena Adamson - One of the best experts on this subject based on the ideXlab platform.
-
Preparing for Ebolavirus disease: specimen collection, packaging and transport.
Pathology, 2015Co-Authors: Sheena Adamson, Roger Wilson, Greg JamesAbstract:Summary Ebolavirus is classified by Standards Australia as a Risk Group 4 pathogen for handling in laboratories. Specimens known or reasonably expected to contain Ebolavirus are classified by the United Nations as Dangerous Goods Infectious Substances Category A, UN 2814, which if transported by air must comply with International Air Transport Association (IATA) Hazard Class 6.2 and Packing Instruction 620 and Civil Aviation Safety Authority (CASA) Regulations. As such high risk pathogens are rarely encountered in pathology laboratories in Australia, the possibility of an imported case of Ebolavirus disease occurring in NSW during the current ongoing outbreak which began in West Africa in 2014 prompted a review and rapid implementation of specific risk management protocols for Ebolavirus testing. Here we describe and report on the management of specimen collection, packaging and transport by public and private pathology laboratories agreed by a task force led by NSW Health Pathology and Health Protection NSW.
