The Experts below are selected from a list of 267 Experts worldwide ranked by ideXlab platform
Byoung Yoon Park - One of the best experts on this subject based on the ideXlab platform.
-
geomechanical model calibration using field measurements for a Petroleum Reserve
Rock Mechanics and Rock Engineering, 2018Co-Authors: Byoung Yoon Park, Steven R. Sobolik, Courtney G HerrickAbstract:A finite element numerical analysis model has been constructed that consists of a mesh that effectively captures the geometries of Bayou Choctaw (BC) Strategic Petroleum Reserve (SPR) site and multimechanism deformation (M-D) salt constitutive model using the daily data of actual wellhead pressure and oil–brine interface location. The salt creep rate is not uniform in the salt dome, and the creep test data for BC salt are limited. Therefore, the model calibration is necessary to simulate the geomechanical behavior of the salt dome. The cavern volumetric closures of SPR caverns calculated from CAVEMAN are used as the field baseline measurement. The structure factor, A2, and transient strain limit factor, K0, in the M-D constitutive model are used for the calibration. The value of A2, obtained experimentally from BC salt, and the value of K0, obtained from Waste Isolation Pilot Plant salt, are used for the baseline values. To adjust the magnitude of A2 and K0, multiplication factors A2F and K0F are defined, respectively. The A2F and K0F values of the salt dome and salt drawdown skins surrounding each SPR cavern have been determined through a number of back analyses. The cavern volumetric closures calculated from this model correspond to the predictions from CAVEMAN for six SPR caverns. Therefore, this model is able to predict behaviors of the salt dome, caverns, caprock, and interbed layers. The geotechnical concerns associated with the BC site from this analysis will be explained in a follow-up paper.
-
Construction of hexahedral finite element mesh capturing realistic geometries of a Petroleum Reserve
Finite Elements in Analysis and Design, 2017Co-Authors: Byoung Yoon Park, Barry L. Roberts, Steven R. SobolikAbstract:Abstract The three-dimensional finite element mesh capturing realistic geometries of the Bayou Choctaw site has been constructed using the sonar and seismic survey data obtained from the field. The mesh consists of hexahedral elements because the salt constitutive model is coded using hexahedral elements. Various ideas and techniques to construct finite element mesh capturing artificially and naturally formed geometries are provided. The techniques to reduce the number of elements as much as possible to save on computer run time while maintaining the computational accuracy is also introduced. The steps and methodologies could be applied to construct the meshes of Big Hill, Bryan Mound, and West Hackberry strategic Petroleum Reserve sites. The methodology could be applied to the complicated shape masses for various civil and geological structures.
-
Interbed Modeling to Predict Wellbore Damage for Big Hill Strategic Petroleum Reserve
Rock Mechanics and Rock Engineering, 2014Co-Authors: Byoung Yoon ParkAbstract:Oil leaks were found in wellbores of Caverns 105 and 109 at the Big Hill Strategic Petroleum Reserve site. According to the field observations, two instances of casing damage occurred at the depth of the interbed between the caprock bottom and salt top. A three-dimensional finite element model, which allows each cavern to be configured individually, was constructed to investigate horizontal and vertical displacements in each well as it crosses the various interbeds. The model contains interfaces between each lithology and a shear zone (fault) to examine the interbed behavior in a realistic manner. This analysis results indicate that the casings of Caverns 105 and 109 failed, respectively, from shear stress that exceeded the casing shear strength due to the horizontal movement of the salt top relative to the caprock and tensile stress due to the downward movement of the salt top from the caprock. The wellbores of Caverns 114 and 104, located at the far end of the field and near the fault, respectively, are predicted to fail by shear stress in the near future. The wellbores of inmost Caverns 107 and 108 are predicted to fail by tensile stress in the near future. The salt top subsides because the volumes of caverns in the salt dome decrease with time due to salt creep closure, while the caprock does not subside at the same rate as the salt top because the caprock is thick and stiff. This discrepancy yields deformation of the well.
-
2013 strategic Petroleum Reserve big hill well integrity grading report.
2014Co-Authors: David L. Lord, Byoung Yoon Park, David Keith Rudeen, Barry L. Roberts, Anna C. Snider Lord, Giorgia Bettin, Steven R. Sobolik, Lisa Eldredge, Karen Wynn, Dean CheckaiAbstract:This report summarizes the work performed in developing a framework for the prioritization of cavern access wells for remediation and monitoring at the Big Hill Strategic Petroleum Reserve site. This framework was then applied to all 28 wells at the Big Hill site with each well receiving a grade for remediation and monitoring. Numerous factors affecting well integrity were incorporated into the grading framework including casing survey results, cavern pressure history, results from geomechanical simulations, and site geologic factors. The framework was developed in a way as to be applicable to all four of the Strategic Petroleum Reserve sites.
-
U.S. strategic Petroleum Reserve Big Hill 114 leak analysis 2012.
2013Co-Authors: David L. Lord, Byoung Yoon Park, Barry L. Roberts, Anna C. Snider Lord, Steven R. Sobolik, David Keith RudeenAbstract:This report addresses recent well integrity issues related to cavern 114 at the Big Hill Strategic Petroleum Reserve site. DM Petroleum Operations, M&O contractor for the U.S. Strategic Petroleum Reserve, recognized an apparent leak in Big Hill cavern well 114A in late summer, 2012, and provided written notice to the State of Texas as required by law. DM has since isolated the leak in well A with a temporary plug, and is planning on remediating both 114 A- and B-wells with liners. In this report Sandia provides an analysis of the apparent leak that includes: (i) estimated leak volume, (ii) recommendation for operating pressure to maintain in the cavern between temporary and permanent fixes for the well integrity issues, and (iii) identification of other caverns or wells at Big Hill that should be monitored closely in light of the sequence of failures there in the last several years.
Gang Wu - One of the best experts on this subject based on the ideXlab platform.
-
a dynamic programming model of china s strategic Petroleum Reserve general strategy and the effect of emergencies
Energy Economics, 2012Co-Authors: Gang Wu, Chris P Nielsen, Xi Lu, Michael B McelroyAbstract:To protect the security of energy supply, China is building national strategic Petroleum Reserve (SPR). We present a dynamic programming model to determine the optimal stockpiling and drawdown strategies for China's SPR under various scenarios, focusing on minimizing the total cost of Reserves. In contrast to previous research, the oil price given in our model is exogenous on a monthly instead of annual basis, with a view to more realistic simulation of optimal strategies each year. Our model results show that in the case where stockpiling affects oil prices, a given SPR size will be achieved earlier than when stockpiling does not affect oil prices. In different emergency conditions, the optimal stockpiling and drawdown strategies of China's SPR are very different. When an emergency occurs, the shock of stockpiling on the oil price per barrel could range $0.49–$6.35, while the impact of drawdown on the oil price per barrel could range −$6.22 to −$0.48.
-
an empirical analysis of the dynamic programming model of stockpile acquisition strategies for china s strategic Petroleum Reserve
Energy Policy, 2008Co-Authors: Gang WuAbstract:The world's future oil price is affected by many factors. The challenge, therefore, is how to select optimal stockpile acquisition strategies to minimize the cost of maintaining a Reserve. This paper provides a new method for analyzing this problem using an uncertain dynamic programming model to analyze stockpile acquisition strategies for strategic Petroleum Reserve. Using this model, we quantify the impact of uncertain world oil price on optimal stockpile acquisition strategies of China's strategic Petroleum Reserve for the period 2007-2010 and 2011-2020. Our results show that the future stockpile acquisition is related to oil prices and their probability and, if not considering the occurrence of oil supply shortage, China should at least purchase 25 million barrels when world oil price is at an optimal level. The optimal price of stockpile acquisition of every year has a stronger relationship with the probability of high price; and the optimal expected price and size of stockpile acquisition is different in each year.
Steven R. Sobolik - One of the best experts on this subject based on the ideXlab platform.
-
geomechanical model calibration using field measurements for a Petroleum Reserve
Rock Mechanics and Rock Engineering, 2018Co-Authors: Byoung Yoon Park, Steven R. Sobolik, Courtney G HerrickAbstract:A finite element numerical analysis model has been constructed that consists of a mesh that effectively captures the geometries of Bayou Choctaw (BC) Strategic Petroleum Reserve (SPR) site and multimechanism deformation (M-D) salt constitutive model using the daily data of actual wellhead pressure and oil–brine interface location. The salt creep rate is not uniform in the salt dome, and the creep test data for BC salt are limited. Therefore, the model calibration is necessary to simulate the geomechanical behavior of the salt dome. The cavern volumetric closures of SPR caverns calculated from CAVEMAN are used as the field baseline measurement. The structure factor, A2, and transient strain limit factor, K0, in the M-D constitutive model are used for the calibration. The value of A2, obtained experimentally from BC salt, and the value of K0, obtained from Waste Isolation Pilot Plant salt, are used for the baseline values. To adjust the magnitude of A2 and K0, multiplication factors A2F and K0F are defined, respectively. The A2F and K0F values of the salt dome and salt drawdown skins surrounding each SPR cavern have been determined through a number of back analyses. The cavern volumetric closures calculated from this model correspond to the predictions from CAVEMAN for six SPR caverns. Therefore, this model is able to predict behaviors of the salt dome, caverns, caprock, and interbed layers. The geotechnical concerns associated with the BC site from this analysis will be explained in a follow-up paper.
-
Construction of hexahedral finite element mesh capturing realistic geometries of a Petroleum Reserve
Finite Elements in Analysis and Design, 2017Co-Authors: Byoung Yoon Park, Barry L. Roberts, Steven R. SobolikAbstract:Abstract The three-dimensional finite element mesh capturing realistic geometries of the Bayou Choctaw site has been constructed using the sonar and seismic survey data obtained from the field. The mesh consists of hexahedral elements because the salt constitutive model is coded using hexahedral elements. Various ideas and techniques to construct finite element mesh capturing artificially and naturally formed geometries are provided. The techniques to reduce the number of elements as much as possible to save on computer run time while maintaining the computational accuracy is also introduced. The steps and methodologies could be applied to construct the meshes of Big Hill, Bryan Mound, and West Hackberry strategic Petroleum Reserve sites. The methodology could be applied to the complicated shape masses for various civil and geological structures.
-
2013 strategic Petroleum Reserve big hill well integrity grading report.
2014Co-Authors: David L. Lord, Byoung Yoon Park, David Keith Rudeen, Barry L. Roberts, Anna C. Snider Lord, Giorgia Bettin, Steven R. Sobolik, Lisa Eldredge, Karen Wynn, Dean CheckaiAbstract:This report summarizes the work performed in developing a framework for the prioritization of cavern access wells for remediation and monitoring at the Big Hill Strategic Petroleum Reserve site. This framework was then applied to all 28 wells at the Big Hill site with each well receiving a grade for remediation and monitoring. Numerous factors affecting well integrity were incorporated into the grading framework including casing survey results, cavern pressure history, results from geomechanical simulations, and site geologic factors. The framework was developed in a way as to be applicable to all four of the Strategic Petroleum Reserve sites.
-
U.S. strategic Petroleum Reserve Big Hill 114 leak analysis 2012.
2013Co-Authors: David L. Lord, Byoung Yoon Park, Barry L. Roberts, Anna C. Snider Lord, Steven R. Sobolik, David Keith RudeenAbstract:This report addresses recent well integrity issues related to cavern 114 at the Big Hill Strategic Petroleum Reserve site. DM Petroleum Operations, M&O contractor for the U.S. Strategic Petroleum Reserve, recognized an apparent leak in Big Hill cavern well 114A in late summer, 2012, and provided written notice to the State of Texas as required by law. DM has since isolated the leak in well A with a temporary plug, and is planning on remediating both 114 A- and B-wells with liners. In this report Sandia provides an analysis of the apparent leak that includes: (i) estimated leak volume, (ii) recommendation for operating pressure to maintain in the cavern between temporary and permanent fixes for the well integrity issues, and (iii) identification of other caverns or wells at Big Hill that should be monitored closely in light of the sequence of failures there in the last several years.
-
analysis of cavern shapes for the strategic Petroleum Reserve
2006Co-Authors: Brian L. Ehgartner, Steven R. SobolikAbstract:This report presents computational analyses to determine the structural integrity of different salt cavern shapes. Three characteristic shapes for increasing cavern volumes are evaluated and compared to the baseline shape of a cylindrical cavern. Caverns with enlarged tops, bottoms, and mid-sections are modeled. The results address pillar to diameter ratios of some existing caverns in the system and will represent the final shape of other caverns if they are repeatedly drawn down. This deliverable is performed in support of the U.S. Strategic Petroleum Reserve. Several three-dimensional models using a close-packed arrangement of 19 caverns have been built and analyzed using a simplified symmetry involving a 30-degree wedge portion of the model. This approach has been used previously for West Hackberry (Ehgartner and Sobolik, 2002) and Big Hill (Park et al., 2005) analyses. A stratigraphy based on the Big Hill site has been incorporated into the model. The caverns are modeled without wells and casing to simplify the calculations. These calculations have been made using the power law creep model. The four cavern shapes were evaluated at several different cavern radii against four design factors. These factors included the dilatant damage safety factor in salt, the cavern volume closure, axial well strain in the caprock, and surface subsidence. The relative performance of each of the cavern shapes varies for the different design factors, although it is apparent that the enlarged bottom design provides the worst overall performance. The results of the calculations are put in the context of the history of cavern analyses assuming cylindrical caverns, and how these results affect previous understanding of cavern behavior in a salt dome.
Barry L. Roberts - One of the best experts on this subject based on the ideXlab platform.
-
Construction of hexahedral finite element mesh capturing realistic geometries of a Petroleum Reserve
Finite Elements in Analysis and Design, 2017Co-Authors: Byoung Yoon Park, Barry L. Roberts, Steven R. SobolikAbstract:Abstract The three-dimensional finite element mesh capturing realistic geometries of the Bayou Choctaw site has been constructed using the sonar and seismic survey data obtained from the field. The mesh consists of hexahedral elements because the salt constitutive model is coded using hexahedral elements. Various ideas and techniques to construct finite element mesh capturing artificially and naturally formed geometries are provided. The techniques to reduce the number of elements as much as possible to save on computer run time while maintaining the computational accuracy is also introduced. The steps and methodologies could be applied to construct the meshes of Big Hill, Bryan Mound, and West Hackberry strategic Petroleum Reserve sites. The methodology could be applied to the complicated shape masses for various civil and geological structures.
-
analysis of multi arm caliper data for the u s strategic Petroleum Reserve
2015Co-Authors: Barry L. RobertsAbstract:The U.S. Strategic Petroleum Reserve (SPR) has an increasing reliance on mul t i - arm caliper surveys to assess the integrity of casing for cavern access wells and to determine priorities for casing remediation. Multi - arm caliper (MAC) surveys provide a view of well casing deformation by reporting radial measurements of the inner cas ing wall as the tool is drawn through the casing. Over the last several years the SPR has collected a large number of modern MAC surveys. In total, these surveys account for over 100 million individual measurements. The surveys were collected using diff ering survey vendors and survey hardware. This has resulted in a collection of disparate data sets which confound attempts to make well - to - well or time - dependent evaluations. In addition, the vendor supplied MAC interpretations often involve variables wh ich are not well defined or which may not be applicable to casings for cavern access wells. These factors reduce the usability of these detailed data sets. In order to address this issue and provide an independent analysis of multi - arm caliper survey data, Sandia National Labs has developed processing techniques and analysis variables which allow for themore » comparison of MAC survey data regardless of the source of the survey data. These techniques use the raw radial arm information and newly developed analysis variables to assess the casing status and provide a means for well - to - well and time - dependent analyses. Well - to - well and t ime - dependent investigation of the MAC survey data provide s information to prioritize well remediation activities and identify wells with integrity issues. This paper presents the challenges in using disparate MAC survey data, techniques developed to address these challenges and some o f the insights gained from these new techniques.« less
-
2013 strategic Petroleum Reserve big hill well integrity grading report.
2014Co-Authors: David L. Lord, Byoung Yoon Park, David Keith Rudeen, Barry L. Roberts, Anna C. Snider Lord, Giorgia Bettin, Steven R. Sobolik, Lisa Eldredge, Karen Wynn, Dean CheckaiAbstract:This report summarizes the work performed in developing a framework for the prioritization of cavern access wells for remediation and monitoring at the Big Hill Strategic Petroleum Reserve site. This framework was then applied to all 28 wells at the Big Hill site with each well receiving a grade for remediation and monitoring. Numerous factors affecting well integrity were incorporated into the grading framework including casing survey results, cavern pressure history, results from geomechanical simulations, and site geologic factors. The framework was developed in a way as to be applicable to all four of the Strategic Petroleum Reserve sites.
-
U.S. strategic Petroleum Reserve Big Hill 114 leak analysis 2012.
2013Co-Authors: David L. Lord, Byoung Yoon Park, Barry L. Roberts, Anna C. Snider Lord, Steven R. Sobolik, David Keith RudeenAbstract:This report addresses recent well integrity issues related to cavern 114 at the Big Hill Strategic Petroleum Reserve site. DM Petroleum Operations, M&O contractor for the U.S. Strategic Petroleum Reserve, recognized an apparent leak in Big Hill cavern well 114A in late summer, 2012, and provided written notice to the State of Texas as required by law. DM has since isolated the leak in well A with a temporary plug, and is planning on remediating both 114 A- and B-wells with liners. In this report Sandia provides an analysis of the apparent leak that includes: (i) estimated leak volume, (ii) recommendation for operating pressure to maintain in the cavern between temporary and permanent fixes for the well integrity issues, and (iii) identification of other caverns or wells at Big Hill that should be monitored closely in light of the sequence of failures there in the last several years.
David L. Lord - One of the best experts on this subject based on the ideXlab platform.
-
2013 strategic Petroleum Reserve big hill well integrity grading report.
2014Co-Authors: David L. Lord, Byoung Yoon Park, David Keith Rudeen, Barry L. Roberts, Anna C. Snider Lord, Giorgia Bettin, Steven R. Sobolik, Lisa Eldredge, Karen Wynn, Dean CheckaiAbstract:This report summarizes the work performed in developing a framework for the prioritization of cavern access wells for remediation and monitoring at the Big Hill Strategic Petroleum Reserve site. This framework was then applied to all 28 wells at the Big Hill site with each well receiving a grade for remediation and monitoring. Numerous factors affecting well integrity were incorporated into the grading framework including casing survey results, cavern pressure history, results from geomechanical simulations, and site geologic factors. The framework was developed in a way as to be applicable to all four of the Strategic Petroleum Reserve sites.
-
Brine-in-crude-oil emulsions at the Strategic Petroleum Reserve.
2013Co-Authors: Martin B. Nemer, David L. Lord, Terry L. MacdonaldAbstract:Metastable water-in-crude-oil emulsion formation could occur in a Strategic Petroleum Reserve (SPR) cavern if water were to flow into the crude-oil layer at a sufficient rate. Such a situation could arise during a drawdown from a cavern with a broken-hanging brine string. A high asphaltene content (> 1.5 wt %) of the crude oil provides the strongest predictor of whether a metastable water-in-crude-oil emulsion will form. However there are many crude oils with an asphaltene content > 1.5 wt % that don't form stable emulsions, but few with a low asphaltene content that do form stable emulsions. Most of the oils that form stable emulsions are %E2%80%9Csour%E2%80%9D by SPR standards indicating they contain total sulfur > 0.50 wt %.
-
U.S. strategic Petroleum Reserve Big Hill 114 leak analysis 2012.
2013Co-Authors: David L. Lord, Byoung Yoon Park, Barry L. Roberts, Anna C. Snider Lord, Steven R. Sobolik, David Keith RudeenAbstract:This report addresses recent well integrity issues related to cavern 114 at the Big Hill Strategic Petroleum Reserve site. DM Petroleum Operations, M&O contractor for the U.S. Strategic Petroleum Reserve, recognized an apparent leak in Big Hill cavern well 114A in late summer, 2012, and provided written notice to the State of Texas as required by law. DM has since isolated the leak in well A with a temporary plug, and is planning on remediating both 114 A- and B-wells with liners. In this report Sandia provides an analysis of the apparent leak that includes: (i) estimated leak volume, (ii) recommendation for operating pressure to maintain in the cavern between temporary and permanent fixes for the well integrity issues, and (iii) identification of other caverns or wells at Big Hill that should be monitored closely in light of the sequence of failures there in the last several years.
-
Quantifying VOC emissions for the strategic Petroleum Reserve.
2013Co-Authors: Robert G. Knowlton, David L. LordAbstract:A very important aspect of the Department of Energy's (DOE's) Strategic Petroleum Reserve (SPR) program is regulatory compliance. One of the regulatory compliance issues deals with limiting the amount of volatile organic compounds (VOCs) that are emitted into the atmosphere from brine wastes when they are discharged to brine holding ponds. The US Environmental Protection Agency (USEPA) has set limits on the amount of VOCs that can be discharged to the atmosphere. Several attempts have been made to quantify the VOC emissions associated with the brine ponds going back to the late 1970's. There are potential issues associated with each of these quantification efforts. Two efforts were made to quantify VOC emissions by analyzing VOC content of brine samples obtained from wells. Efforts to measure air concentrations were mentioned in historical reports but no data have been located to confirm these assertions. A modeling effort was also performed to quantify the VOC emissions. More recently in 2011- 2013, additional brine sampling has been performed to update the VOC emissions estimate. An analysis of the statistical confidence in these results is presented here. Arguably, there are uncertainties associated with each of these efforts. The analysis herein indicates that the upper confidencemore » limit in VOC emissions based on recent brine sampling is very close to the 0.42 ton/MMB limit used historically on the project. Refining this estimate would require considerable investment in additional sampling, analysis, and monitoring. An analysis of the VOC emissions at each site suggests that additional discharges could be made and stay within current regulatory limits.« less
-
Summary of Degas II performance at the US Strategic Petroleum Reserve Big Hill site.
2007Co-Authors: David Keith Rudeen, David L. LordAbstract:Crude oil stored at the US Strategic Petroleum Reserve (SPR) requires mitigation procedures to maintain oil vapor pressure within program delivery standards. Crude oil degasification is one effective method for lowering crude oil vapor pressure, and was implemented at the Big Hill SPR site from 2004-2006. Performance monitoring during and after degasification revealed a range of outcomes for caverns that had similar inventory and geometry. This report analyzed data from SPR degasification and developed a simple degas mixing (SDM) model to assist in the analysis. Cavern-scale oil mixing during degassing and existing oil heterogeneity in the caverns were identified as likely causes for the range of behaviors seen. Apparent cavern mixing patterns ranged from near complete mixing to near plug flow, with more mixing leading to less efficient degassing due to degassed oil re-entering the plant before 100% of the cavern oil volume was processed. The report suggests that the new cavern bubble point and vapor pressure regain rate after degassing be based on direct in-cavern measurements after degassing as opposed to using the plant outlet stream properties as a starting point, which understates starting bubble point and overstates vapor pressure regain. Several means to estimate the cavern bubble point after degas in the absence of direct measurement are presented and discussed.