The Experts below are selected from a list of 5826 Experts worldwide ranked by ideXlab platform

Hui Sun - One of the best experts on this subject based on the ideXlab platform.

  • Preparation and Characterization of Electrospun PLCL/Poloxamer Nanofibers and Dextran/Gelatin Hydrogels for Skin Tissue Engineering
    PLoS ONE, 2014
    Co-Authors: Jian-feng Pan, Ning-hua Liu, Hui Sun
    Abstract:

    In this study, two different biomaterials were fabricated and their potential use as a bilayer scaffold for Skin Tissue Engineering applications was assessed. The upper layer biomaterial was a Poly(e-caprolactone-co-lactide)/Poloxamer (PLCL/Poloxamer) nanofiber membrane fabricated using electrospinning technology. The PLCL/Poloxamer nanofibers (PLCL/Poloxamer, 9/1) exhibited strong mechanical properties (stress/strain values of 9.37±0.38 MPa/187.43±10.66%) and good biocompatibility to support adipose-derived stem cells proliferation. The lower layer biomaterial was a hydrogel composed of 10% dextran and 20% gelatin without the addition of a chemical crosslinking agent. The 5/5 dextran/gelatin hydrogel displayed high swelling property, good compressive strength, capacity to present more than 3 weeks and was able to support cells proliferation. A bilayer scaffold was fabricated using these two materials by underlaying the nanofibers and casting hydrogel to mimic the structure and biological function of native Skin Tissue. The upper layer membrane provided mechanical support in the scaffold and the lower layer hydrogel provided adequate space to allow cells to proliferate and generate extracellular matrix. The biocompatibility of bilayer scaffold was preliminarily investigated to assess the potential cytotoxicity. The results show that cell viability had not been affected when cocultured with bilayer scaffold. As a consequence, the bilayer scaffold composed of PLCL/Poloxamer nanofibers and dextran/gelatin hydrogels is biocompatible and possesses its potentially high application prospect in the field of Skin Tissue Engineering.

  • preparation and characterization of electrospun plcl poloxamer nanofibers and dextran gelatin hydrogels for Skin Tissue Engineering
    PLOS ONE, 2014
    Co-Authors: Jian-feng Pan, Ning-hua Liu, Hui Sun
    Abstract:

    In this study, two different biomaterials were fabricated and their potential use as a bilayer scaffold for Skin Tissue Engineering applications was assessed. The upper layer biomaterial was a Poly(e-caprolactone-co-lactide)/Poloxamer (PLCL/Poloxamer) nanofiber membrane fabricated using electrospinning technology. The PLCL/Poloxamer nanofibers (PLCL/Poloxamer, 9/1) exhibited strong mechanical properties (stress/strain values of 9.37±0.38 MPa/187.43±10.66%) and good biocompatibility to support adipose-derived stem cells proliferation. The lower layer biomaterial was a hydrogel composed of 10% dextran and 20% gelatin without the addition of a chemical crosslinking agent. The 5/5 dextran/gelatin hydrogel displayed high swelling property, good compressive strength, capacity to present more than 3 weeks and was able to support cells proliferation. A bilayer scaffold was fabricated using these two materials by underlaying the nanofibers and casting hydrogel to mimic the structure and biological function of native Skin Tissue. The upper layer membrane provided mechanical support in the scaffold and the lower layer hydrogel provided adequate space to allow cells to proliferate and generate extracellular matrix. The biocompatibility of bilayer scaffold was preliminarily investigated to assess the potential cytotoxicity. The results show that cell viability had not been affected when cocultured with bilayer scaffold. As a consequence, the bilayer scaffold composed of PLCL/Poloxamer nanofibers and dextran/gelatin hydrogels is biocompatible and possesses its potentially high application prospect in the field of Skin Tissue Engineering.

  • Electrospinning of poly (ε-caprolactone-co-lactide)/Pluronic blended scaffolds for Skin Tissue Engineering
    Journal of Materials Science, 2014
    Co-Authors: Ning-hua Liu, Jian-feng Pan, Yue-e Miao, Tianxi Liu, Hui Sun
    Abstract:

    For Skin Tissue Engineering, an ideal scaffold should mimic the natural extracellular matrix of the native Skin. In this study, we reported a novel elastic sub-micron fiber scaffold blending poly (e-caprolactone-co-lactide) (PLCL) and Pluronic at different ratios by electrospinning. PLCL and Pluronic were co-electrospun with the ratio of 100/0, 99/1, 95/5, 90/10, 85/15, and 75/25. These scaffolds were evaluated in terms of fiber morphology, mechanical properties, and hydrophilicity for the purpose of culturing adipose-derived stem cells (ADSCs). Cell attachment and proliferation on the scaffolds were also evaluated to demonstrate the potential of serving as a Skin graft. The results indicated that all of the electrospun fibers possessed smooth surface textures and interconnected porous structures with the average diameter ranging from approximately 750–1140 nm. The higher tensile strength was observed in 95/5 and 90/10 PLCL/Pluronic blended membranes, while further incorporation of Pluronic almost has no effect on tensile strength. The water contact angle was 85° for scaffold with the ratio of 99/1, while 0° for 90/10, 85/15, and 75/25. In addition, the elevation of Pluronic content in composition resulted in a corresponding increase in swelling behavior. Compared with PLCL, the better cell adhesion and proliferation potential of ADSCs was exhibited on all PLCL/Pluronic blended scaffolds. ADSCs on the blended scaffolds were highly elongated and well integrated with the surrounding fibers, indicating the good cytocompatibility of PLCL/Pluronic scaffolds. Thus, these blended scaffolds have the potentially high application prospect in the field of Skin Tissue Engineering.

  • electrospinning of poly e caprolactone co lactide pluronic blended scaffolds for Skin Tissue Engineering
    Journal of Materials Science, 2014
    Co-Authors: Ning-hua Liu, Jian-feng Pan, Yue-e Miao, Tianxi Liu, Hui Sun
    Abstract:

    For Skin Tissue Engineering, an ideal scaffold should mimic the natural extracellular matrix of the native Skin. In this study, we reported a novel elastic sub-micron fiber scaffold blending poly (e-caprolactone-co-lactide) (PLCL) and Pluronic at different ratios by electrospinning. PLCL and Pluronic were co-electrospun with the ratio of 100/0, 99/1, 95/5, 90/10, 85/15, and 75/25. These scaffolds were evaluated in terms of fiber morphology, mechanical properties, and hydrophilicity for the purpose of culturing adipose-derived stem cells (ADSCs). Cell attachment and proliferation on the scaffolds were also evaluated to demonstrate the potential of serving as a Skin graft. The results indicated that all of the electrospun fibers possessed smooth surface textures and interconnected porous structures with the average diameter ranging from approximately 750–1140 nm. The higher tensile strength was observed in 95/5 and 90/10 PLCL/Pluronic blended membranes, while further incorporation of Pluronic almost has no effect on tensile strength. The water contact angle was 85° for scaffold with the ratio of 99/1, while 0° for 90/10, 85/15, and 75/25. In addition, the elevation of Pluronic content in composition resulted in a corresponding increase in swelling behavior. Compared with PLCL, the better cell adhesion and proliferation potential of ADSCs was exhibited on all PLCL/Pluronic blended scaffolds. ADSCs on the blended scaffolds were highly elongated and well integrated with the surrounding fibers, indicating the good cytocompatibility of PLCL/Pluronic scaffolds. Thus, these blended scaffolds have the potentially high application prospect in the field of Skin Tissue Engineering.

Rangasamy Jayakumar - One of the best experts on this subject based on the ideXlab platform.

  • fabrication of chitosan poly caprolactone nanofibrous scaffold for bone and Skin Tissue Engineering
    International Journal of Biological Macromolecules, 2011
    Co-Authors: K.t. Shalumon, K.h. Anulekha, Krishna Prasad Chennazhi, Hiroshi Tamura, S.v. Nair, Rangasamy Jayakumar
    Abstract:

    Chitosan/poly(caprolactone) (CS/PCL) nanofibrous scaffold was prepared by a single step electrospinning technique. The presence of CS in CS/PCL scaffold aided a significant improvement in the hydrophilicity of the scaffold as confirmed by a decrease in contact angle, which thereby enhanced bioactivity and protein adsorption on the scaffold. The cyto-compatibility of the CS/PCL scaffold was examined using human osteoscarcoma cells (MG63) and found to be non toxic. Moreover, CS/PCL scaffold was found to support the attachment and proliferation of various cell lines such as mouse embryo fibroblasts (NIH3T3), murine aneuploid fibro sarcoma (L929), and MG63 cells. Cell attachment and proliferation was further confirmed by nuclear staining using 4',6-diamidino-2-phenylindole (DAPI). All these results indicate that CS/PCL nanofibrous scaffold would be an excellent system for bone and Skin Tissue Engineering.

  • Fabrication of chitosan/poly(caprolactone) nanofibrous scaffold for bone and Skin Tissue Engineering
    International Journal of Biological Macromolecules, 2011
    Co-Authors: K.t. Shalumon, K.h. Anulekha, Krishna Prasad Chennazhi, Hiroshi Tamura, S.v. Nair, Rangasamy Jayakumar
    Abstract:

    Chitosan/poly(caprolactone) (CS/PCL) nanofibrous scaffold was prepared by a single step electrospinning technique. The presence of CS in CS/PCL scaffold aided a significant improvement in the hydrophilicity of the scaffold as confirmed by a decrease in contact angle, which thereby enhanced bioactivity and protein adsorption on the scaffold. The cyto-compatibility of the CS/PCL scaffold was examined using human osteoscarcoma cells (MG63) and found to be non toxic. Moreover, CS/PCL scaffold was found to support the attachment and proliferation of various cell lines such as mouse embryo fibroblasts (NIH3T3), murine aneuploid fibro sarcoma (L929), and MG63 cells. Cell attachment and proliferation was further confirmed by nuclear staining using 4',6-diamidino-2-phenylindole (DAPI). All these results indicate that CS/PCL nanofibrous scaffold would be an excellent system for bone and Skin Tissue Engineering.

Jian-feng Pan - One of the best experts on this subject based on the ideXlab platform.

  • Preparation and Characterization of Electrospun PLCL/Poloxamer Nanofibers and Dextran/Gelatin Hydrogels for Skin Tissue Engineering
    PLoS ONE, 2014
    Co-Authors: Jian-feng Pan, Ning-hua Liu, Hui Sun
    Abstract:

    In this study, two different biomaterials were fabricated and their potential use as a bilayer scaffold for Skin Tissue Engineering applications was assessed. The upper layer biomaterial was a Poly(e-caprolactone-co-lactide)/Poloxamer (PLCL/Poloxamer) nanofiber membrane fabricated using electrospinning technology. The PLCL/Poloxamer nanofibers (PLCL/Poloxamer, 9/1) exhibited strong mechanical properties (stress/strain values of 9.37±0.38 MPa/187.43±10.66%) and good biocompatibility to support adipose-derived stem cells proliferation. The lower layer biomaterial was a hydrogel composed of 10% dextran and 20% gelatin without the addition of a chemical crosslinking agent. The 5/5 dextran/gelatin hydrogel displayed high swelling property, good compressive strength, capacity to present more than 3 weeks and was able to support cells proliferation. A bilayer scaffold was fabricated using these two materials by underlaying the nanofibers and casting hydrogel to mimic the structure and biological function of native Skin Tissue. The upper layer membrane provided mechanical support in the scaffold and the lower layer hydrogel provided adequate space to allow cells to proliferate and generate extracellular matrix. The biocompatibility of bilayer scaffold was preliminarily investigated to assess the potential cytotoxicity. The results show that cell viability had not been affected when cocultured with bilayer scaffold. As a consequence, the bilayer scaffold composed of PLCL/Poloxamer nanofibers and dextran/gelatin hydrogels is biocompatible and possesses its potentially high application prospect in the field of Skin Tissue Engineering.

  • preparation and characterization of electrospun plcl poloxamer nanofibers and dextran gelatin hydrogels for Skin Tissue Engineering
    PLOS ONE, 2014
    Co-Authors: Jian-feng Pan, Ning-hua Liu, Hui Sun
    Abstract:

    In this study, two different biomaterials were fabricated and their potential use as a bilayer scaffold for Skin Tissue Engineering applications was assessed. The upper layer biomaterial was a Poly(e-caprolactone-co-lactide)/Poloxamer (PLCL/Poloxamer) nanofiber membrane fabricated using electrospinning technology. The PLCL/Poloxamer nanofibers (PLCL/Poloxamer, 9/1) exhibited strong mechanical properties (stress/strain values of 9.37±0.38 MPa/187.43±10.66%) and good biocompatibility to support adipose-derived stem cells proliferation. The lower layer biomaterial was a hydrogel composed of 10% dextran and 20% gelatin without the addition of a chemical crosslinking agent. The 5/5 dextran/gelatin hydrogel displayed high swelling property, good compressive strength, capacity to present more than 3 weeks and was able to support cells proliferation. A bilayer scaffold was fabricated using these two materials by underlaying the nanofibers and casting hydrogel to mimic the structure and biological function of native Skin Tissue. The upper layer membrane provided mechanical support in the scaffold and the lower layer hydrogel provided adequate space to allow cells to proliferate and generate extracellular matrix. The biocompatibility of bilayer scaffold was preliminarily investigated to assess the potential cytotoxicity. The results show that cell viability had not been affected when cocultured with bilayer scaffold. As a consequence, the bilayer scaffold composed of PLCL/Poloxamer nanofibers and dextran/gelatin hydrogels is biocompatible and possesses its potentially high application prospect in the field of Skin Tissue Engineering.

  • Electrospinning of poly (ε-caprolactone-co-lactide)/Pluronic blended scaffolds for Skin Tissue Engineering
    Journal of Materials Science, 2014
    Co-Authors: Ning-hua Liu, Jian-feng Pan, Yue-e Miao, Tianxi Liu, Hui Sun
    Abstract:

    For Skin Tissue Engineering, an ideal scaffold should mimic the natural extracellular matrix of the native Skin. In this study, we reported a novel elastic sub-micron fiber scaffold blending poly (e-caprolactone-co-lactide) (PLCL) and Pluronic at different ratios by electrospinning. PLCL and Pluronic were co-electrospun with the ratio of 100/0, 99/1, 95/5, 90/10, 85/15, and 75/25. These scaffolds were evaluated in terms of fiber morphology, mechanical properties, and hydrophilicity for the purpose of culturing adipose-derived stem cells (ADSCs). Cell attachment and proliferation on the scaffolds were also evaluated to demonstrate the potential of serving as a Skin graft. The results indicated that all of the electrospun fibers possessed smooth surface textures and interconnected porous structures with the average diameter ranging from approximately 750–1140 nm. The higher tensile strength was observed in 95/5 and 90/10 PLCL/Pluronic blended membranes, while further incorporation of Pluronic almost has no effect on tensile strength. The water contact angle was 85° for scaffold with the ratio of 99/1, while 0° for 90/10, 85/15, and 75/25. In addition, the elevation of Pluronic content in composition resulted in a corresponding increase in swelling behavior. Compared with PLCL, the better cell adhesion and proliferation potential of ADSCs was exhibited on all PLCL/Pluronic blended scaffolds. ADSCs on the blended scaffolds were highly elongated and well integrated with the surrounding fibers, indicating the good cytocompatibility of PLCL/Pluronic scaffolds. Thus, these blended scaffolds have the potentially high application prospect in the field of Skin Tissue Engineering.

  • electrospinning of poly e caprolactone co lactide pluronic blended scaffolds for Skin Tissue Engineering
    Journal of Materials Science, 2014
    Co-Authors: Ning-hua Liu, Jian-feng Pan, Yue-e Miao, Tianxi Liu, Hui Sun
    Abstract:

    For Skin Tissue Engineering, an ideal scaffold should mimic the natural extracellular matrix of the native Skin. In this study, we reported a novel elastic sub-micron fiber scaffold blending poly (e-caprolactone-co-lactide) (PLCL) and Pluronic at different ratios by electrospinning. PLCL and Pluronic were co-electrospun with the ratio of 100/0, 99/1, 95/5, 90/10, 85/15, and 75/25. These scaffolds were evaluated in terms of fiber morphology, mechanical properties, and hydrophilicity for the purpose of culturing adipose-derived stem cells (ADSCs). Cell attachment and proliferation on the scaffolds were also evaluated to demonstrate the potential of serving as a Skin graft. The results indicated that all of the electrospun fibers possessed smooth surface textures and interconnected porous structures with the average diameter ranging from approximately 750–1140 nm. The higher tensile strength was observed in 95/5 and 90/10 PLCL/Pluronic blended membranes, while further incorporation of Pluronic almost has no effect on tensile strength. The water contact angle was 85° for scaffold with the ratio of 99/1, while 0° for 90/10, 85/15, and 75/25. In addition, the elevation of Pluronic content in composition resulted in a corresponding increase in swelling behavior. Compared with PLCL, the better cell adhesion and proliferation potential of ADSCs was exhibited on all PLCL/Pluronic blended scaffolds. ADSCs on the blended scaffolds were highly elongated and well integrated with the surrounding fibers, indicating the good cytocompatibility of PLCL/Pluronic scaffolds. Thus, these blended scaffolds have the potentially high application prospect in the field of Skin Tissue Engineering.

K.t. Shalumon - One of the best experts on this subject based on the ideXlab platform.

  • fabrication of chitosan poly caprolactone nanofibrous scaffold for bone and Skin Tissue Engineering
    International Journal of Biological Macromolecules, 2011
    Co-Authors: K.t. Shalumon, K.h. Anulekha, Krishna Prasad Chennazhi, Hiroshi Tamura, S.v. Nair, Rangasamy Jayakumar
    Abstract:

    Chitosan/poly(caprolactone) (CS/PCL) nanofibrous scaffold was prepared by a single step electrospinning technique. The presence of CS in CS/PCL scaffold aided a significant improvement in the hydrophilicity of the scaffold as confirmed by a decrease in contact angle, which thereby enhanced bioactivity and protein adsorption on the scaffold. The cyto-compatibility of the CS/PCL scaffold was examined using human osteoscarcoma cells (MG63) and found to be non toxic. Moreover, CS/PCL scaffold was found to support the attachment and proliferation of various cell lines such as mouse embryo fibroblasts (NIH3T3), murine aneuploid fibro sarcoma (L929), and MG63 cells. Cell attachment and proliferation was further confirmed by nuclear staining using 4',6-diamidino-2-phenylindole (DAPI). All these results indicate that CS/PCL nanofibrous scaffold would be an excellent system for bone and Skin Tissue Engineering.

  • Fabrication of chitosan/poly(caprolactone) nanofibrous scaffold for bone and Skin Tissue Engineering
    International Journal of Biological Macromolecules, 2011
    Co-Authors: K.t. Shalumon, K.h. Anulekha, Krishna Prasad Chennazhi, Hiroshi Tamura, S.v. Nair, Rangasamy Jayakumar
    Abstract:

    Chitosan/poly(caprolactone) (CS/PCL) nanofibrous scaffold was prepared by a single step electrospinning technique. The presence of CS in CS/PCL scaffold aided a significant improvement in the hydrophilicity of the scaffold as confirmed by a decrease in contact angle, which thereby enhanced bioactivity and protein adsorption on the scaffold. The cyto-compatibility of the CS/PCL scaffold was examined using human osteoscarcoma cells (MG63) and found to be non toxic. Moreover, CS/PCL scaffold was found to support the attachment and proliferation of various cell lines such as mouse embryo fibroblasts (NIH3T3), murine aneuploid fibro sarcoma (L929), and MG63 cells. Cell attachment and proliferation was further confirmed by nuclear staining using 4',6-diamidino-2-phenylindole (DAPI). All these results indicate that CS/PCL nanofibrous scaffold would be an excellent system for bone and Skin Tissue Engineering.

Ning-hua Liu - One of the best experts on this subject based on the ideXlab platform.

  • Preparation and Characterization of Electrospun PLCL/Poloxamer Nanofibers and Dextran/Gelatin Hydrogels for Skin Tissue Engineering
    PLoS ONE, 2014
    Co-Authors: Jian-feng Pan, Ning-hua Liu, Hui Sun
    Abstract:

    In this study, two different biomaterials were fabricated and their potential use as a bilayer scaffold for Skin Tissue Engineering applications was assessed. The upper layer biomaterial was a Poly(e-caprolactone-co-lactide)/Poloxamer (PLCL/Poloxamer) nanofiber membrane fabricated using electrospinning technology. The PLCL/Poloxamer nanofibers (PLCL/Poloxamer, 9/1) exhibited strong mechanical properties (stress/strain values of 9.37±0.38 MPa/187.43±10.66%) and good biocompatibility to support adipose-derived stem cells proliferation. The lower layer biomaterial was a hydrogel composed of 10% dextran and 20% gelatin without the addition of a chemical crosslinking agent. The 5/5 dextran/gelatin hydrogel displayed high swelling property, good compressive strength, capacity to present more than 3 weeks and was able to support cells proliferation. A bilayer scaffold was fabricated using these two materials by underlaying the nanofibers and casting hydrogel to mimic the structure and biological function of native Skin Tissue. The upper layer membrane provided mechanical support in the scaffold and the lower layer hydrogel provided adequate space to allow cells to proliferate and generate extracellular matrix. The biocompatibility of bilayer scaffold was preliminarily investigated to assess the potential cytotoxicity. The results show that cell viability had not been affected when cocultured with bilayer scaffold. As a consequence, the bilayer scaffold composed of PLCL/Poloxamer nanofibers and dextran/gelatin hydrogels is biocompatible and possesses its potentially high application prospect in the field of Skin Tissue Engineering.

  • preparation and characterization of electrospun plcl poloxamer nanofibers and dextran gelatin hydrogels for Skin Tissue Engineering
    PLOS ONE, 2014
    Co-Authors: Jian-feng Pan, Ning-hua Liu, Hui Sun
    Abstract:

    In this study, two different biomaterials were fabricated and their potential use as a bilayer scaffold for Skin Tissue Engineering applications was assessed. The upper layer biomaterial was a Poly(e-caprolactone-co-lactide)/Poloxamer (PLCL/Poloxamer) nanofiber membrane fabricated using electrospinning technology. The PLCL/Poloxamer nanofibers (PLCL/Poloxamer, 9/1) exhibited strong mechanical properties (stress/strain values of 9.37±0.38 MPa/187.43±10.66%) and good biocompatibility to support adipose-derived stem cells proliferation. The lower layer biomaterial was a hydrogel composed of 10% dextran and 20% gelatin without the addition of a chemical crosslinking agent. The 5/5 dextran/gelatin hydrogel displayed high swelling property, good compressive strength, capacity to present more than 3 weeks and was able to support cells proliferation. A bilayer scaffold was fabricated using these two materials by underlaying the nanofibers and casting hydrogel to mimic the structure and biological function of native Skin Tissue. The upper layer membrane provided mechanical support in the scaffold and the lower layer hydrogel provided adequate space to allow cells to proliferate and generate extracellular matrix. The biocompatibility of bilayer scaffold was preliminarily investigated to assess the potential cytotoxicity. The results show that cell viability had not been affected when cocultured with bilayer scaffold. As a consequence, the bilayer scaffold composed of PLCL/Poloxamer nanofibers and dextran/gelatin hydrogels is biocompatible and possesses its potentially high application prospect in the field of Skin Tissue Engineering.

  • Electrospinning of poly (ε-caprolactone-co-lactide)/Pluronic blended scaffolds for Skin Tissue Engineering
    Journal of Materials Science, 2014
    Co-Authors: Ning-hua Liu, Jian-feng Pan, Yue-e Miao, Tianxi Liu, Hui Sun
    Abstract:

    For Skin Tissue Engineering, an ideal scaffold should mimic the natural extracellular matrix of the native Skin. In this study, we reported a novel elastic sub-micron fiber scaffold blending poly (e-caprolactone-co-lactide) (PLCL) and Pluronic at different ratios by electrospinning. PLCL and Pluronic were co-electrospun with the ratio of 100/0, 99/1, 95/5, 90/10, 85/15, and 75/25. These scaffolds were evaluated in terms of fiber morphology, mechanical properties, and hydrophilicity for the purpose of culturing adipose-derived stem cells (ADSCs). Cell attachment and proliferation on the scaffolds were also evaluated to demonstrate the potential of serving as a Skin graft. The results indicated that all of the electrospun fibers possessed smooth surface textures and interconnected porous structures with the average diameter ranging from approximately 750–1140 nm. The higher tensile strength was observed in 95/5 and 90/10 PLCL/Pluronic blended membranes, while further incorporation of Pluronic almost has no effect on tensile strength. The water contact angle was 85° for scaffold with the ratio of 99/1, while 0° for 90/10, 85/15, and 75/25. In addition, the elevation of Pluronic content in composition resulted in a corresponding increase in swelling behavior. Compared with PLCL, the better cell adhesion and proliferation potential of ADSCs was exhibited on all PLCL/Pluronic blended scaffolds. ADSCs on the blended scaffolds were highly elongated and well integrated with the surrounding fibers, indicating the good cytocompatibility of PLCL/Pluronic scaffolds. Thus, these blended scaffolds have the potentially high application prospect in the field of Skin Tissue Engineering.

  • electrospinning of poly e caprolactone co lactide pluronic blended scaffolds for Skin Tissue Engineering
    Journal of Materials Science, 2014
    Co-Authors: Ning-hua Liu, Jian-feng Pan, Yue-e Miao, Tianxi Liu, Hui Sun
    Abstract:

    For Skin Tissue Engineering, an ideal scaffold should mimic the natural extracellular matrix of the native Skin. In this study, we reported a novel elastic sub-micron fiber scaffold blending poly (e-caprolactone-co-lactide) (PLCL) and Pluronic at different ratios by electrospinning. PLCL and Pluronic were co-electrospun with the ratio of 100/0, 99/1, 95/5, 90/10, 85/15, and 75/25. These scaffolds were evaluated in terms of fiber morphology, mechanical properties, and hydrophilicity for the purpose of culturing adipose-derived stem cells (ADSCs). Cell attachment and proliferation on the scaffolds were also evaluated to demonstrate the potential of serving as a Skin graft. The results indicated that all of the electrospun fibers possessed smooth surface textures and interconnected porous structures with the average diameter ranging from approximately 750–1140 nm. The higher tensile strength was observed in 95/5 and 90/10 PLCL/Pluronic blended membranes, while further incorporation of Pluronic almost has no effect on tensile strength. The water contact angle was 85° for scaffold with the ratio of 99/1, while 0° for 90/10, 85/15, and 75/25. In addition, the elevation of Pluronic content in composition resulted in a corresponding increase in swelling behavior. Compared with PLCL, the better cell adhesion and proliferation potential of ADSCs was exhibited on all PLCL/Pluronic blended scaffolds. ADSCs on the blended scaffolds were highly elongated and well integrated with the surrounding fibers, indicating the good cytocompatibility of PLCL/Pluronic scaffolds. Thus, these blended scaffolds have the potentially high application prospect in the field of Skin Tissue Engineering.